كحد أقصى. الحالية: | 630A | كحد أقصى. الجهد: | 11KV |
---|---|---|---|
اساسي: | iec | تيار مصنّف: | 630A |
جهد فلطيّ مصنّف: | الحياة الميكانيكية: | 10000 | |
الكلمات الرئيسية: | ميناء: | Ningbo | |
تسليط الضوء: | load break isolator,high voltage isolator switch,high voltage isolator switch |
بند | وحدة | البيانات | |
تردد الطاقة مع جهد الوقوف | كا |
42
|
48
|
التصنيف الحالي | أ |
400
|
630
|
تيار مستقر حراري (4 ث) | أ |
12.5
|
20
|
تيار مستقر ديناميكي (الذروة) | كا |
31.5
|
50
|
تصنيف كسر الحالي | أ |
400
|
630
|
تيار قطع الدائرة القصيرة | كا |
31.5
|
50
|
نموذج | الفولطية / KA | التصنيف الحالي / A | التصنيف الحالي للفيوزات / أ |
SDLA.J |
12
|
50
|
6.3،10،16،20،25،31.5،40 |
SFLA.J |
12
|
100
|
50،63،71،80،100 |
SKLA.J |
12
|
125
|
125
|
ما الفرق بين Load Break Switch و Circuit Breaker
هناك معلمتان مختلفتان مهمتان فيما يتعلق بفصل / توصيل المرافق الكهربائية.
- قدرة كسر.
- صنع القدرات.
زيادة القدرة على التصنيع نظرًا لأنها تدرس تيار البدء الأولي ، والاندفاع والأعطال التي قد تحدث عند التبديل في اللحظة.
Accordingly, the Circuit breakers have both while the Isolator or LBS has only breaking capacity. وفقا لذلك ، فإن قواطع الدائرة لديها كلاهما بينما المعزل أو LBS لديه قدرة كسر فقط. Isolator therefore used to isolate/disconnect/break load. وبالتالي يستخدم العازل لعزل / فصل / كسر الحمل. To be switched on only under no load. ليتم تشغيله فقط دون تحميل.
Basically and LBS is only designed to make and break load currents. في الأساس ، تم تصميم LBS فقط لكسر تيارات الحمل وكسرها. It can be closed onto a fault (has a making rating) and cannot break a fault current. يمكن إغلاقه على خطأ (لديه تصنيف صنع) ولا يمكن كسر تيار خطأ. A CB is designed to make and break fault currents and off course load currents. تم تصميم CB لتصنيع وكسر تيارات الأعطال وتيارات حمل الحمل خارج المسار. Need to be careful with switching long cables and long lines with LBS, due to its limitation with switching cable/line charging (highly capacitive) currents. تحتاج إلى توخي الحذر عند تبديل الكابلات الطويلة والخطوط الطويلة باستخدام LBS ، نظرًا لقصرها على تبديل تيارات شحن الكابلات / الخط (السعة العالية). Similar precaution with needed with switching reactive loads like large transformers. احتياطات مماثلة عند الحاجة مع تبديل الأحمال التفاعلية مثل المحولات الكبيرة. Normally a CB is recommended for the 2 latter cases. عادة يوصى باستخدام CB في الحالتين الأخيرتين. Check the manufacturer test specs. تحقق من مواصفات اختبار الشركة المصنعة.
In simple way the Load Break Switch used to cut off healthy circuits or to break / disconnect the load. بطريقة بسيطة يستخدم مفتاح كسر الحمل لقطع الدوائر الصحية أو لكسر / فصل الحمل. As a precaution, normally the LBS / Isolator are to be switched on under no load, the connected load to be utilized after switching on the Isolator. كإجراء وقائي ، عادة ما يتم تشغيل LBS / المعزل تحت أي حمل ، يتم استخدام الحمل المتصل بعد تشغيل المعزل. This why it has no making capacity. لهذا السبب ليس لديها القدرة على صنع. Circuit Breakers are intended to operate under unnormal conditions in order to clear the fault & to isolate the defective circuits protecting its associated electrical equipment, therefore breaking and making capacities are considered as the most important criteria as far Circuit breaker are concerned. الغرض من قواطع الدائرة هو العمل في ظل ظروف غير طبيعية من أجل إزالة العطل وعزل الدوائر المعيبة التي تحمي المعدات الكهربائية المرتبطة بها ، وبالتالي تعتبر قدرات التكسير والتصنيع أهم المعايير فيما يتعلق بقواطع الدائرة.
The making current is not an RMS value it is the peak value ie. تيار صنع ليس قيمة RMS بل قيمة الذروة أي. Impk = 2.5Irms. Impk = 2.5Irms. The peak value of 2.5 times RMS is the DC offset at point when the LBS closes on the fault and is taken as the worst case X/R ratio of the source (X/R of about 20). تبلغ قيمة الذروة 2.5 مرة RMS هو إزاحة التيار المستمر عند النقطة عندما يغلق LBS على الخطأ ويتم اعتباره أسوأ حالة X / R للمصدر (X / R من حوالي 20). This peak decays to RMS value Ith (thermal withstand current) dependent on the X/R delay constant. يتحلل هذا الذروة إلى قيمة RMS Ith (تيار الصمود الحراري) الذي يعتمد على ثابت التأخير X / R. The decay rate is exponential with time. معدل الاضمحلال أسي مع مرور الوقت. There is a misconception that making is 2.5times breaking current, but making is normally quoted as a peak and breaking as RMS. هناك اعتقاد خاطئ بأن الصنع هو كسر التيار 2.5 مرة ، ولكن عادة ما يتم اقتباس التصنيع على أنه ذروة وكسر مثل RMS. The breaking current in a CB is an RMS value. تيار الكسر في CB هو قيمة RMS. Breaking fault current is far more difficult that making especially when the contacts open when current is not at zero crossing point on the sine wave. كسر تيار العطل هو أكثر صعوبة بكثير ، خاصة عند فتح جهات الاتصال عندما لا يكون التيار عند نقطة عبور صفر على الموجة الجيبية. For HV systems 132KV and above, the restrike and TRV starts to become a major consideration in CB selection, especially for long cables and lines. بالنسبة لأنظمة الجهد العالي 132 كيلوفولت وما فوق ، يبدأ الريستريك و TRV في أن يصبح أحد الاعتبارات الرئيسية في اختيار CB ، خاصة للكابلات والخطوط الطويلة.